16-289.fm Page 1 Tuesday, July 20, 1999 10:57 AM
Cat. No. 16-289
OWNER’S MANUAL
Please read before using this equipment.
13-Inch Color TV/Monitor
16-289.fm Page 3 Tuesday, July 20, 1999 10:57 AM
SAFETY PRECAUTIONS
Warning: To prevent fire or shock
hazard, do not expose this product
to rain or moisture.
Power Supply: This TV operates on
120V, 60 Hz AC power only. Never
connect the TV to a voltage other than
the specified voltage (such as to the
output of a nontransformer type con-
verter or to direct current).
CAUTION
RISK OF ELECTRIC SHOCK.
!
DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER OR BACK. NO USER-SERVICE-
ABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED PERSONNEL.
Polarized Plug: This TV is equipped
with a polarized plug (one blade is wid-
er than the other). This plug fits into an
AC power outlet only one way. If you
are unable to fully insert the plug into
the outlet, try reversing the plug.
This symbol is intended to alert you
to the presence of uninsulated dan-
gerous voltage within the product’s
enclosure that might be of sufficient
magnitude to constitute a risk of
electric shock. Do not open the
product’s case.
Installation: Do not expose the TV to
any unnecessary jarring, moisture,
dust, direct sunlight, or heat.
Select a place for this TV that minimiz-
es the length of the antenna lead and
power cord.
This symbol is intended to inform
you that important operating and
maintenance instructions are in-
cluded in the literature accompany-
ing this product.
!
Allow sufficient space between the TV
and wall so the chassis components
are properly ventilated.
Do not cover the ventilation slots on
the top or back of the TV or place the
TV on any soft material that could af-
fect ventilation on the bottom of the TV.
3
16-289.fm Page 4 Tuesday, July 20, 1999 10:57 AM
CONTENTS
Getting Started ..................................................................................................... 5
Choosing a Location ........................................................................................ 5
Connecting Antennas ...................................................................................... 5
Connecting an Outdoor Antenna .............................................................. 5
Connecting Cable TV ...................................................................................... 6
Connecting an Audio/Video Source ................................................................. 7
Connecting Power ........................................................................................... 7
Connecting Earphones .................................................................................... 7
Installing the Remote Control’s Batteries ........................................................ 8
Using the TV’s Controls ...................................................................................... 9
Using the TV’s Front Panel Controls ............................................................... 9
Using the Remote Control ............................................................................. 10
Using Auto Demonstration ............................................................................. 11
Operation ............................................................................................................ 12
Turning the TV On/Off ................................................................................... 12
Setting the On-Screen Language .................................................................. 12
Selecting the Input Signal .............................................................................. 12
Selecting TV or Video .................................................................................... 13
Using Automatic and Manual Channel Programming .................................... 13
Using Automatic Programming ............................................................... 13
Manually Adding a Channel .................................................................... 13
Manually Deleting a Channel .................................................................. 14
Auto Picture Control ...................................................................................... 15
Adjusting the Picture ...................................................................................... 15
Special Functions .............................................................................................. 17
Setting the Sleep Timer ................................................................................. 17
Using Closed Captions .................................................................................. 17
Selecting the Caption Function ............................................................... 19
Using the Text Function ................................................................................. 19
Selecting Text .......................................................................................... 20
Troubleshooting ................................................................................................. 21
Care and Maintenance ....................................................................................... 22
FCC Information ............................................................................................ 23
Specifications ..................................................................................................... 24
4
16-289.fm Page 5 Tuesday, July 20, 1999 10:57 AM
GETTING STARTED
Connecting an Outdoor
Antenna
CHOOSING A LOCATION
Choose a location for the TV where:
• Air flows freely on all sides.
For the best reception, we recommend
you use an outdoor antenna.
• The power cord is not in the way
of normal traffic.
Note: Before you connect the TV to an
outdoor antenna, inspect the antenna
and the antenna’s cable. Severely
weathered antennas and antenna ca-
bles can reduce the signal quality.
Your local Radio Shack store sells re-
placement antenna cable (300-ohm
flat wire or 75-ohm coaxial cable) and
a wide variety of outdoor antennas.
Note: Do not plug in the power cord
until you make all other connections.
CONNECTING
ANTENNAS
The supplied rod antenna provides ad-
equate reception in most areas.
The antenna connection you use de-
pends on the type of antenna and ca-
ble you have.
To connect the rod antenna, insert it
into the hole on the top of the TV. At-
tach the 300-ohm twin-lead connec-
tors to the two screw terminals on the
supplied adapter.
Warning: When installing an outdoor
antenna, read and follow all instruc-
tions and cautions that accompany the
antenna.
• If you have a combination VHF/
UHF antenna and the antenna
uses 75-ohm coaxial cable, con-
nect the cable directly to the TV’s
VHF/UHF (75Ω) terminal.
300 Ohm Flat Wire
300-to-75 Ohm Adapter
Then connect the adapter to the TV’s
VHF/UHF Antenna
VHF/UHF (75Ω) terminal.
VHF/UHF (75Ω) Terminal
75 Ohm Coaxial Cable
Rod Antenna
300-to-75 Ohm Adapter
VHF/UHF (75Ω) Terminal
5
16-289.fm Page 6 Tuesday, July 20, 1999 10:57 AM
• If you have a combination VHF/
UHF antenna and the antenna
uses 300-ohm flat wire, connect
the flat wire to the screw terminals
on the supplied 300-to-75 ohm
adapter. Then connect the
adapter to the TV’s VHF/UHF (75Ω)
terminal.
CONNECTING CABLE TV
If you subscribe to a cable TV service,
connect the cable company’s 75-ohm
coaxial cable directly to the TV’s VHF/
UHF (75Ω) terminal.
If you use a cable box, connect the
box’s output to the TV’s VHF/UHF (75Ω)
terminal.
VHF/UHF (75Ω) Terminal
VHF/UHF Antenna
From Cable Company
75-Ohm Coaxial Cable
300-to-75 Ohm Adapter
300 Ohm Flat Wire
OUT
IN
Cable Box
• If you have separate VHF and
UHF antennas, use a VHF/UHF
combiner (not supplied) to com-
bine the VHF and UHF signals.
Then connect the combiner’s 75-
ohm connector to the TV’s VHF/
UHF (75Ω) terminal.
Set the TV to the same channel as the
box’s output (Channel 3 or 4) and use
the box to select channels.
This
Note to CATV System Installer:
reminder is provided to call the CATV
system installer’s attention to Section
820-40 of the NEC which provides
guidelines for proper grounding and, in
particular, specifies that the cable
ground shall be connected to the
grounding system of the building, as
close to the point of cable entry as
practical.
VHF Antenna
UHF Antenna
VHF/UHF (75Ω) Terminal
VHF/UHF Combiner
You can listen to your TV by connect-
ing an earphone to the TV’s EAR-
PHONE jack, or by connecting the TV’s
AUDIO IN/VIDEO IN jacks to a home
audio system.
6
16-289.fm Page 7 Tuesday, July 20, 1999 10:57 AM
CONNECTING AN
AUDIO/VIDEO SOURCE
CONNECTING
EARPHONES
You can use your TV to monitor an au-
dio/video source (such as a VCR, cam-
corder or laser disc player). Connect
the audio/video source’s output jacks
For private listening, plug a pair of ear-
phones with a /8-inch mini-plug (not
1
EARPHONE
supplied) into the
jack on
the right side of the TV.
AUDIO IN/VIDEO IN
to the
jacks on the
back of the TV.
EARHONE
AUDIO IN
VIDEO IN
Listening Safely
To view the audio/video source, follow
the steps in “Selecting TV or Video”
and play the audio/video source ac-
cording to its instructions.
To protect your hearing, follow these
guidelines when you use earphones.
• Set the volume to the lowest set-
ting before you begin listening. Af-
ter you begin listening, adjust the
volume to a comfortable level.
EARPHONE
Note: If you use the
jack,
VOLUME
use the TV’s
the volume.
control to adjust
• Do not listen at extremely high
volume levels. Extended high-
volume listening can lead to per-
manent hearing loss.
CONNECTING POWER
Plug the TV’s AC power cord into a
standard AC power outlet.
• Once you set the volume, do not
increase it. Over time, your ears
adapt to the volume level, so a
volume level that does not cause
discomfort might still damage your
hearing.
7
16-289.fm Page 8 Tuesday, July 20, 1999 10:57 AM
INSTALLING THE
REMOTE CONTROL’S
BATTERIES
The remote control requires two AA
batteries (not supplied) for operation.
For the longest battery life, use alka-
line batteries (Radio Shack Cat. No.
23-552). To ensure consistent opera-
tion, change the batteries about once a
year.
Batteries
1. Remove the battery compartment
cover by pressing down and slid-
ing it in the direction of the arrow.
2. Install two AA batteries as indi-
cated by the polarity markings (+
and –) inside the compartment.
Cautions:
• Batteries installed incorrectly
might leak and damage the
remote control.
• Do not mix old batteries with
new ones, and do not mix differ-
ent types of batteries (for exam-
ple, standard and alkaline).
3. Replace the cover.
8
16-289.fm Page 9 Tuesday, July 20, 1999 10:57 AM
USING THE TV’S CONTROLS
USING THE TV’S FRONT PANEL CONTROLS
This section briefly describes the function of each button on the TV’s front panel.
Each function is described in detail later in this manual.
Remote Control Receiver
FUNCTION — Selects the different on-
CH — Press the top CH
button
to se-
screen function controls.
lect the next higher channel and the
bottom CH button to select the next
lower channel. Press and hold down
either button to quickly scroll through
channels. See “Using Automatic and
Manual Channel Programming” on
Page 13.
VOL — Press the top VOL button to in-
crease the volume and bottom VOL
button to lower it. The number of verti-
cal bars at the lower part of the screen
indicates the relative volume level. You
also use these buttons to adjust the
TV’s on-screen function controls.
POWER — Turns on or off the TV.
9
16-289.fm Page 10 Tuesday, July 20, 1999 10:57 AM
Channel Selection (Number) But-
tons — Press to directly select a chan-
nel. The selected channel number
appears on the screen for about 5 sec-
onds.
USING THE REMOTE
CONTROL
The remote control has the same con-
trols as the TV’s front panel, as well as
the additional controls described in this
section.
• To select a single-digit broadcast
(AIR) channel — Channel 5, for
5
example — press . You do not
0
To operate the remote control, point its
front window toward the TV’s front
panel. Then press the desired but-
ton(s) on the remote control.
need to press before entering a
single-digit channel (but, if you do,
the TV changes channels faster).
• To select a double-digit broadcast
channel — Channel 12, for exam-
Channel Selection Buttons
1
2
ple — press and then .
• To select a three-digit cable chan-
nel — Channel 121, for example
1 2
1
— press , , and .
Note: You must select CABLEas
the input source before you can
select a cable channel. See “Se-
lecting the Input Signal” on
Page 12.
RECALL
— Displays the current chan-
nel number for about 5 seconds. Also
clears the on-screen function displays.
SLEEP
— Sets the sleep timer.
PICTURE
— Selects a picture control
(contrast, brightness, color, tint, or
sharpness) for adjustment.
TV/VIDEO
— Selects the TV or VIDEO
mode.
CAPTION
— Turns the closed caption
decoder on or off.
10
16-289.fm Page 11 Tuesday, July 20, 1999 10:57 AM
REVIEW — Returns to the previously
selected channel.
USING AUTO
DEMONSTRATION
MUTE — Press once to mute the
sound. MUTE appears on the screen.
Press again to restore the sound.
Auto demonstration lets you see all the
on-screen controls.
1. Press SET-UP on the remote con-
trol until AUTODEMO.appears on
the screen.
APC (Auto Picture Control) — Returns
to the factory preset picture settings or
the settings you select.
SET-UP — Selects the different on-
screen function controls. (This button
is similar to the FUNCTION button on
the TV; however, it only performs set-
up operations.)
2. Press VOL or – to start the dem-
+
onstration. The screen shows the
different controls and adjusts
them so you can see how each
one works.
When the demonstration reaches
the last display, it starts again
from the beginning.
3. To stop auto demonstration, press
any button on the remote control
or front panel. The picture returns
to the settings selected before the
demonstration.
11
16-289.fm Page 12 Tuesday, July 20, 1999 10:57 AM
OPERATION
TURNING THE TV
ON/OFF
SELECTING THE INPUT
SIGNAL
Press POWER on the TV’s front panel
or remote control to turn the TV on or
off.
Follow these steps to select between
receiving cable stations and receiving
broadcast channels.
1. Press SET-UP on the remote con-
trol or FUNCTION on the front
panel until INPUT SELECTION
appears on the screen.
SETTING THE ON-
SCREEN LANGUAGE
1. Press SET-UP on the remote con-
trol or FUNCTION on the front
panel until LANGUAGE appears
on the screen.
SET-UP on
Note: When you press
the remote control, VIDEO does
not appear as a selection. Press
TV/VIDEO on the remote control to
select VIDEO (see “Selecting TV
or Video” on Page 13).
2. Press VOL + or – so the arrow
points to ENGLISHor ESPANOL
(Spanish).
2. Press VOL + or – so the arrow
points to AIR, CABLE, or VIDEO.
3. The on-screen display automati-
cally clears in about 5 seconds.
Or, you can press RECALL to
clear it.
Select AIRif you are using an an-
tenna or CABLEif you are using a
cable service. Select VIDEO to
view the audio/video source con-
nected to the TV’s input jacks.
All on-screen displays are now in
the selected language.
3. The on-screen display automati-
cally clears in about 5 seconds.
Or, you can press RECALL to
clear it.
12
16-289.fm Page 13 Tuesday, July 20, 1999 10:57 AM
SELECTING TV OR
VIDEO
TV/VIDEO
Press
on the remote control
to view the selected input signal (TV)
or the audio/video source connected to
the TV’s input jacks (VIDEO).
VOL
3. Press
+ or –. The TV auto-
matically scans and memorizes all
active channels in your area.
USING AUTOMATIC AND
MANUAL CHANNEL
PROGRAMMING
Note: You can press any button
on the remote control or front
panel to stop automatic program-
ming.
When you turn on the TV for the first
time, use the automatic channel pro-
gramming feature to scan and memo-
rize all active broadcast and cable
channels in your area. If there are ad-
ditional channels you want to add or
delete, you can manually add or delete
them.
When the TV has scanned and
stored all active channels, it stops
on the nearest programmed chan-
nel to where you started.
CH
Now, when you press
+ or –, the TV
skips inactive channels.
Note: If the TV is unplugged for more
than 24 hours, you must repeat auto-
matic channel programming to restore
channels in memory.
Using Automatic
Programming
TV/VIDEO
1. Press
so TVis selected.
Manually Adding a Channel
SET-UP
2. Press
on the remote con-
FUNCTION
panel until AUTO PROGRAM ap-
pears on the screen.
trol or
on the front
To add a channel that was not stored
during automatic programming, follow
these steps.
TV/VIDEO
1. Press
so TVis selected.
13
16-289.fm Page 14 Tuesday, July 20, 1999 10:57 AM
2. Select the input signal (AIR or
Manually Deleting a Channel
CABLE).
If the TV stored a channel you do not
want, follow these steps to delete the
channel from memory.
1. Press TV/VIDEO so TVis selected.
2. Select the input signal (AIR or
CABLE).
3. Use the remote control’s number
button(s) to select the channel
you want to store.
3. Press CH
or – or the remote
+
control’s number button(s) to se-
lect the channel you want to de-
lete.
4. Press SET-UP on the remote con-
trol until the channel number,
ADD, and DELETEappear on the
screen.
4. Press SET-UP on the remote con-
trol until the channel number,
ADD, and DELETEappear on the
screen.
5. Press VOL
or – so the arrow
+
points to ADD.
6. The on-screen display automati-
cally clears in about 5 seconds.
Or, you can press RECALL to
clear it. The channel is added.
14
16-289.fm Page 15 Tuesday, July 20, 1999 10:57 AM
5. Press VOL
or – so the arrow
appears. If you want to return to the
picture controls you previously select-
ed, press APC until PICTURERESET
OFFappears.
+
points to DELETE.
ADJUSTING THE
PICTURE
6. The on-screen display automati-
cally clears in about 5 seconds.
Or, you can press RECALL to
clear it. The channel is deleted.
Follow these steps to adjust the pic-
ture’s contrast, brightness, color inten-
sity, tint, and sharpness.
1. Press PICTURE on the remote
control or FUNCTION on the front
panel until the desired picture con-
trol appears.
2. Adjust the selected control level
by pressing VOL or .
+
–
AUTO PICTURE
CONTROL
Press APC on the remote control to
display the Auto Picture Control status.
When PICTURERESETis set to ON,
the TV’s picture shows the factory set-
tings. If you adjust the picture, ONau-
tomatically changes to OFF (see
“Adjusting the Picture”).
The bar graph on the screen
shows the relative adjustment
level.
If you have adjusted the picture and
want to return to the factory settings,
press APC until PICTURERESETON
15
16-289.fm Page 16 Tuesday, July 20, 1999 10:57 AM
Refer to the following picture control
chart.
CONTROL
BUTTON
CONTROL
–
+
CONTRAST
BRIGHTNESS
COLOR INTENSITY
TINT
Lower
Darker
Lighter
Reddish
Softer
Higher
Brighter
Deeper
Greenish
Sharper
SHARPNESS
16
16-289.fm Page 17 Tuesday, July 20, 1999 10:57 AM
SPECIAL FUNCTIONS
SETTING THE SLEEP
TIMER
USING CLOSED
CAPTIONS
You can set the sleep timer to auto-
matically turn off the television after the
selected time period.
Closed captioning displays the audio
portion of a television program as writ-
ten words that appear on the television
screen (in a form similar to English
subtitles). Closed captions allow view-
ers to read the dialogue and narration
of television programs.
Follow these steps to use the sleep
timer.
1. Press SLEEP on the remote con-
trol until the desired time period
appears on the screen: ---,
240, 210, 180, 150, 120, 90,
60, 30, 20, or 10minutes.
Caption signals are transmitted as part
of the TV broadcast and then decoded
by the TV to display as words.
SLEEP---
SLEEP10
SLEEP24
SLEEP210
...
SLEEP20
SLEEP30
SLEEP60
Caption Tips
2. Wait about 5 seconds for the dis-
play to automatically clear. The
timer begins to count down for the
selected number of minutes.
• Sometimes TV stations broadcast
two different caption signals on
the same channel. By selecting
MODE 1or MODE 2under MODE
SELECTION, you can choose
which signal to view. MODE 1 is
usually the signal with the cap-
tions, while MODE 2might show
demonstration or programming in-
formation.
Notes:
• To view the remaining sleep time,
press SLEEP once. After about 5
seconds, the display clears.
• To cancel the sleep timer, press
SLEEP until the display shows
SLEEP ---. After about 5 sec-
onds, the display clears.
• Not all TV broadcasts include
closed caption signals. Check
your local programming guide.
17
16-289.fm Page 18 Tuesday, July 20, 1999 10:57 AM
• Your TV might not properly re-
ceive caption signals in the follow-
ing situations.
Ignition: Black spots or horizontal
streaks appear; picture flutters or
drifts. Usually caused by interfer-
ence from an automobile ignition
system, neon lamps, drills, or oth-
er electrical appliances.
You are using an old, bad, or ille-
gally recorded tape in the VCR
connected to the TV.
An airplane or car is interfering
with the TV signal.
The signal from the antenna is
weak.
The program wasn’t captioned
when it was produced, transmit-
ted, or taped.
Ghosts: Double images appear.
Ghosts are caused by the televi-
sion signal following two paths: the
direct path and another reflected
from a building, hill, or other object.
Changing the direction or position
of the antenna might improve the
reception.
• If you connect a VCR that has a
captioning function, note the fol-
lowing.
For the best reception of caption
signals, connect a signal distribu-
tor as shown.
75-Ohm Antenna Jack
CATV Output Terminal
Signal Distributor
Back of TV
Antenna Input Terminal
Back of VCR
Snow: Small dots in the picture. If
your TV is located at the fringe
area of a television broadcast,
where the signal is weak, you
might need to install a special an-
tenna to improve the picture.
TV Input Terminal
18
16-289.fm Page 19 Tuesday, July 20, 1999 10:57 AM
Select the caption function for ei-
ther the TV or the VCR, but not
both. If both are decoding caption
signals, captions might overlap or
reception might be poor.
4. To turn off captions, press CAP-
TION or FUNCTION so DECODER
appears, then press VOL + or – so
the arrow points to OFF.
Selecting the Caption
Function
1. Press CAPTION on the remote
control or FUNCTION on the front
panel so DECODER appears.
Then press VOL + or – so the ar-
row points to ON.
Note: If you select captioning and then
turn off the TV, captioning is still active
when you turn on the TV again.
USING THE TEXT
FUNCTION
Text is information presented in a
black box on the television screen as a
service to viewers. Some examples of
text broadcasts are captioned program
lists, weather forecasts, stock ex-
change reports, and wire-service
news.
2. Press CAPTION or FUNCTION so
DECODER MODE appears. Then
press VOL + or – so the arrow
points to CAPTION.
3. Press CAPTION or FUNCTION until
MODE SELECTION appears.
Press VOL + or – so the arrow
points to MODE 1or MODE 2.
Some television stations provide two
different text services. You can choose
between the two text signals by select-
ing MODE 1 or MODE 2 under MODE
SELECTION.
Note: Not all television stations pro-
vide text services.
19
16-289.fm Page 20 Tuesday, July 20, 1999 10:57 AM
Note: If the signal for the text program
is weak, the black box might appear
and disappear on the screen. This
problem goes away when reception
improves.
Selecting Text
1. Press CAPTION on the remote
control or FUNCTION on the front
panel to display DECODER. Then
press VOL + or – so the arrow
points to ON.
2. Press CAPTION or FUNCTION so
the display shows DECODER
MODE. Then press VOL + or – so
the arrow points to TEXT.
3. Press CAPTION or FUNCTION so
the display shows MODESELEC-
TIONand press VOL + or – so the
arrow points to MODE 1 or MODE
2.
4. To turn off the text function, press
CAPTION or FUNCTION so DE-
CODER appears, then press VOL
+ or – so the arrow points to OFF.
20
16-289.fm Page 21 Tuesday, July 20, 1999 10:57 AM
TROUBLESHOOTING
If you have problems with your 13-inch Color TV/Monitor, review the suggestions be-
low. If you cannot eliminate the problem, contact your local Radio Shack store for
assistance.
Problem
Suggestion
No power.
Make sure the power cord is plugged in
Make sure the television is turned on.
Try another channel.
No picture or sound.
Sound is OK; picture is poor.
Poor reception.
Check the Air, Cable, or Video setting.
Check all connections.
Try another channel (station trouble).
Check all connections.
Adjust the picture controls.
Adjust the antenna.
Check all connections.
Might be local interference.
Try another channel (station trouble).
Adjust the antenna.
Lines in picture or ghosts (multiple
images).
Adjust the picture controls.
Check all connections.
Might be local interference.
Check batteries in the remote control.
Remote control doesn’t work.
Cannot tune to the desired channel. Try another channel (station trouble).
Check the Air, Cable, or Video setting.
Channel might not be programmed in channel
memory. Store it using auto or manual program-
ming.
21
16-289.fm Page 22 Tuesday, July 20, 1999 10:57 AM
CARE AND MAINTENANCE
Your Radio Shack 13-Inch Color TV/Monitor is an example of superior design and
craftsmanship. The following suggestions will help you care for your TV/Monitor so
you can enjoy it for years.
Keep the TV/Monitor dry. If it gets wet, wipe it dry immediately. Liq-
uids might contain minerals that can corrode the electronic circuits.
Handle the TV/Monitor gently and carefully. Dropping it can damage
circuit boards and cases and can cause the TV/Monitor to work im-
properly.
Use and store the TV/Monitor only in normal temperature environ-
ments. Temperature extremes can shorten the life of electronic de-
vices and distort or melt plastic parts.
Keep the TV/Monitor away from dust and dirt, which can cause pre-
mature wear of parts.
Wipe the TV/Monitor with a damp cloth occasionally to keep it looking
CLEANER
new. Do not use harsh chemicals, cleaning solvents, or strong deter-
gents to clean the TV/Monitor.
Modifying or tampering with the TV/Monitor’s internal components can cause a mal-
function and might invalidate your TV/Monitor’s warranty and void your FCC autho-
rization to operate it. If your TV/Monitor is not performing as it should, take it to your
local Radio Shack store for assistance.
22
16-289.fm Page 23 Tuesday, July 20, 1999 10:57 AM
FCC INFORMATION
This TV/Monitor complies with the lim-
its for a Class B digital device as spec-
ified in Part 15 of FCC Rules. These
limits provide reasonable protection
against radio and TV interference in a
residential area. However, your TV/
Monitor might cause TV or radio inter-
ference even when it is operating prop-
erly. To eliminate interference, you can
try one or more of the following correc-
tive measures:
• Reorient or relocate the receiving
antenna.
• Increase the distance between the
TV/Monitor and the radio or TV.
• Use outlets on different electrical
circuits for the TV/Monitor and the
radio or TV.
Consult your local Radio Shack store
or an experienced radio/TV technician
if the problem still exists.
You must use shielded cables with this
equipment.
23
16-289.fm Page 24 Tuesday, July 20, 1999 10:57 AM
SPECIFICATIONS
System ....................................................................................................... NTSC-M
Picture Tube ....................................................................... Type No. A34KPU02XX
Horizontal Resolution ............................................................................... 260 Lines
Receiving Channels ............................................................. Broadcast VHF: 2∠13
Broadcast UHF: 14∠69
CATV: 1∠125
Intermediate Frequency .......................... Picture IF Carrier Frequency: 45.75 MHz
Sound IF Carrier Frequency: 41.25 MHz
Color Sub-Carrier Frequency: 42.17 MHz
Maximum Sensitivity .................... VHF: 28 dB µV max; UHF/CATV: 32 dB µV max
Antenna .................................................................. VHF/UHF 75-Ohm Unbalanced
Power Source ................................................................................. AC 120V, 60Hz
Power Consumption ........................................................................ 85 W Maximum
Output Power ................................................................................. 1.2 W Maximum
Load Impedance ....................................................................................... 16 Ohms
Frequency Response ............................................. 80 Hz–7 kHz (3 dB Bandwidth)
Total Harmonic Distortion ................................................................................... 2%
Speaker ............................................................... 16 Ohm 1.5 Watt (Maximum 3W)
Input Level:
Video .................................................................... 1 Vp-p (75-Ohm Terminated)
Audio ............................................................................................. 400 mV rms
Dimensions (HWD) .............. 143/4 × 146/7 × 142/9 Inches (375 × 377.5 × 361.5 mm)
Weight ......................................................................................... 17 lb 8 oz (7.9 kg)
Specifications are typical; individual units might vary. Specifications are subject to
change and improvement without notice.
24
16-289.fm Page 25 Tuesday, July 20, 1999 10:57 AM
NOTES
25
16-289.fm Page 26 Tuesday, July 20, 1999 10:57 AM
26
16-289.fm Page 27 Tuesday, July 20, 1999 10:57 AM
27
16-289.fm Page 28 Tuesday, July 20, 1999 10:57 AM
RADIO SHACK LIMITED WARRANTY
This product is warranted against defects for 90 days from date of purchase from Radio
Shack company-owned stores and authorized Radio Shack franchisees and dealers.
Within this period, we will repair it without charge for parts and labor. Simply bring your
Radio Shack sales slip as proof of purchase date to any Radio Shack store. Warranty
does not cover transportation costs. Nor does it cover a product subjected to misuse or
accidental damage.
EXCEPT AS PROVIDED HEREIN, RADIO SHACK MAKES NO EXPRESS WARRAN-
TIES AND ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURA-
TION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. Some states
do not permit limitation or exclusion of implied warranties; therefore, the aforesaid limi-
tation(s) or exclusion(s) may not apply to the purchaser.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state.
We Service What We Sell
9/94
RADIO SHACK
A Division of Tandy Corporation
Fort Worth, Texas 76102
P/N 482-H59L
1A7
Printed in Mexico
|